StudentPilot.com is a PilotMall.com publicationShop pilot supplies ›

Traffic Pattern: Legs, Altitude, Entry and Radio Calls

The airport traffic pattern is a standard rectangular path around a runway: departure and upwind, crosswind, downwind, base and final. Unless the airport publishes something else, all turns are to the left and propeller airplanes fly it at 1,000 feet above ground level (AGL). You normally join the downwind leg at a 45 degree angle, abeam the middle of the runway, already level at pattern altitude.

This guide follows the FAA’s own sources: the Aeronautical Information Manual (AIM) paragraphs 4-3-2 to 4-3-4 (Change 3, effective July 9, 2026), Advisory Circular 90-66C, Non-Towered Airport Flight Operations, and 14 CFR 91.126 and 91.127. It is part of our airport operations guide.

Traffic pattern diagram: the legs

Standard left-hand traffic pattern showing departure and upwind, crosswind, downwind, base and final legs, the 45 degree entry to downwind abeam midfield, and the 45 degree departure exit Approach endDeparture end Downwind Crosswind Base Final Upwind / departure 45 degree entry join abeam midfield Straight out 45 degree exit Left traffic. Pattern altitude typically 1,000 ft AGL (propeller) Wind from the right: land toward the right, into the wind
A standard left-hand pattern for a runway where landings are made toward the right of the drawing. Not to scale. Diagram by StudentPilot.com based on AIM 4-3-3 and AC 90-66C, Appendix A.

The AIM defines each component so pilots and controllers use the same words:

  • Departure: the path straight ahead after takeoff along the extended centerline. The departure climb continues to at least 1/2 mile beyond the departure end of the runway and to within 300 feet of pattern altitude.
  • Upwind leg: a continuation of the departure path, straight ahead on the extended centerline. Controllers use it for spacing and sequencing. (AC 90-66C defines the upwind leg a little differently, as a path parallel to the landing runway in the direction of landing.)
  • Crosswind leg: a path at right angles to the landing runway off its takeoff end.
  • Downwind leg: a path parallel to the landing runway, flown in the opposite direction to landing.
  • Base leg: a path at right angles to the runway off its approach end, from downwind to the extended centerline.
  • Final approach: the path in the direction of landing along the extended centerline, from base to the runway.

The FAA notes that its component diagram shows terminology only, not how to enter. Entry is covered next.

Traffic pattern altitude

AIM 4-3-3 recommends these entry altitudes unless the Chart Supplement publishes a different pattern altitude, or you need a lower one to keep the cloud clearances in 14 CFR 91.155:

Aircraft Recommended pattern altitude
Propeller-driven airplanes 1,000 ft AGL
Large and turbine-powered airplanes Not less than 1,500 ft AGL, or 500 ft above the established pattern altitude
Helicopters About 500 ft AGL, closer to the runway, avoiding the flow of fixed-wing traffic

Pattern altitude is above ground level, so add it to field elevation. An airport at 450 feet MSL has a 1,450 foot MSL pattern for a trainer. Always check the airport’s Chart Supplement entry first: many airports publish their own traffic pattern altitude, and a common altitude is what makes everyone easy to see.

Write the field elevation, pattern altitude (MSL), CTAF and any right-traffic runways on your kneeboard before every flight to a new airport. Doing the math on downwind is how pilots end up 300 feet high or low.

Left turns, right traffic and how it is charted

Standard traffic is left-hand. At an airport without an operating control tower in Class G airspace, 14 CFR 91.126(b) requires pilots of powered fixed-wing aircraft approaching to land to make all turns to the left, unless approved light signals or visual markings tell you to turn right. Section 91.127 applies the same rule to airports in Class E airspace. At a towered airport, AIM 4-3-2 says fixed-wing aircraft circle to the left unless the tower directs otherwise, and you need a landing clearance either way.

Airports set up right traffic for terrain, obstacles or noise. On sectional and VFR terminal area charts, right traffic is shown at the bottom of the airport data block with “RP” followed by the runways, for example RP 9, 18, 22R. “RP*” means special conditions exist and you should read the Chart Supplement. Right patterns are not shown for airports with full-time towers, because the tower assigns the pattern. For more on reading the data block, see our sectional chart guide.

Segmented circle and wind indicators

At a non-towered airport, look for the segmented circle, a ring on the field that groups the visual indicators described in AIM 4-3-4:

  • Wind direction indicator: a wind cone, wind sock or wind tee. The large end of the sock points into the wind, as does the cross bar of a wind tee.
  • Landing direction indicator: a tetrahedron, where installed; its small end points in the direction of landing. Use caution in light or calm winds, when it may not match the calm-wind runway.
  • Landing strip indicators: pairs of markers outside the circle showing the runway alignments.
  • Traffic pattern indicators: markers paired with the landing strip indicators that show the direction of turns when the pattern is not the normal left pattern. Mentally enlarge the indicator for your runway and the base and final legs become obvious.

AC 90-66C suggests checking these indicators from above pattern altitude, then flying well clear of the pattern before descending to pattern altitude to enter. Runway numbers and markings help confirm what you see; our runway markings and airport signs guides cover them.

How to enter the traffic pattern

The FAA regulates pattern flow (the direction of turns), not entry, but AC 90-66C and AIM 4-3-3 give clear recommendations:

  1. Arrive at pattern altitude. Level off well clear of the pattern and allow time to look at the whole pattern. Entries while descending can put you on top of traffic already there.
  2. Enter on the 45. Join the downwind leg at a 45 degree angle, abeam the midpoint of the runway, in level flight at pattern altitude.
  3. Fly downwind at pattern altitude until at least abeam the approach end of the landing runway, then begin the descent.
  4. Turn base at roughly 45 degrees relative bearing from the approach end (AC 90-66C).
  5. Complete the turn to final at least 1/4 mile from the runway (AIM FIG 4-3-3).

Arriving from the other side: midfield crossing

If you arrive from the upwind side (the side opposite downwind), Appendix A of AC 90-66C shows two options. The preferred method: overfly the airport 500 feet above pattern altitude, fly clear of the pattern on the downwind side (about 2 miles), descend to pattern altitude, turn back inbound and join the downwind on the 45 while yielding to downwind traffic. The alternate method: cross midfield at pattern altitude, yield to traffic on the 45 and on downwind, then turn onto downwind. The AC says not to use the midfield crossing when the pattern is congested.

Straight-in approaches

The FAA discourages VFR straight-in approaches because of collision risk. If you choose one, AIM 4-1-9 says to self-announce on the CTAF about 8 to 10 miles out and coordinate with pattern traffic. A straight-in pilot has no priority over aircraft in the pattern and must follow the right-of-way rules in 14 CFR 91.113(g): the lower aircraft has the right-of-way but may not cut in front of an aircraft on final.

Departing the traffic pattern

After takeoff, continue straight ahead until beyond the departure end of the runway. If you are staying in the pattern, turn crosswind beyond the departure end and within 300 feet of pattern altitude. If you are leaving, AIM 4-3-3 and AC 90-66C say to continue straight out, or exit with a 45 degree turn beyond the departure end after reaching pattern altitude: to the left from a left-hand pattern, to the right from a right-hand pattern. Watch for traffic entering on the 45 before you turn.

Towered vs non-towered patterns

Non-towered (or tower closed) Towered
Who sequences Pilots, by radio and see-and-avoid The tower controller
Radio Self-announce on CTAF (radio not required by Part 91, but strongly recommended) Two-way radio contact required (91.126(d) and 91.127(c); in Class D, before entering the airspace under 91.129)
Turn direction Left unless marked or charted right (91.126(b)) As the tower instructs
Entry 45 to downwind recommended As cleared (“enter left downwind runway 27”)

At a towered field you still fly the same legs, but you fly them where the tower tells you, and you may get “extend downwind” or “make right traffic.” Our towered airport communications guide covers those calls, and light gun signals cover what to do if your radio fails. Controlled airspace around towers is explained in our Class D airspace guide.

CTAF radio calls in the pattern

At a non-towered airport, AIM 4-1-9 recommends monitoring and self-announcing on the CTAF from 10 miles out to landing, and departing aircraft from start-up until 10 miles away. Report about 10 miles out, entering downwind, base and final, and when leaving the runway. Say the airport name at the start and end of every call, use the runway number instead of “active runway,” and never say “traffic in the area, please advise.” AC 90-66C adds that you should not announce your own landing sequence (“number three”); at towered airports, sequencing is ATC’s job. If no CTAF is published, use MULTICOM 122.9. The full practice is in our CTAF guide.

Traffic pattern radio calls
Non-towered airport, self-announce on CTAF (AIM 4-1-9, AC 90-66C)
  1. 10 miles out: “Pine Valley traffic, Cessna 1234X, 10 miles south, 2,500, inbound for landing, Pine Valley.”
  2. On the 45: “Pine Valley traffic, Cessna 1234X, entering left downwind runway 27, full stop, Pine Valley.”
  3. Base: “Pine Valley traffic, Cessna 1234X, left base runway 27, Pine Valley.”
  4. Final: “Pine Valley traffic, Cessna 1234X, final runway 27, full stop, Pine Valley.”
  5. Clear: “Pine Valley traffic, Cessna 1234X, clear of runway 27, Pine Valley.”
  6. Taxi out: “Pine Valley traffic, Cessna 1234X, main ramp, taxiing to runway 27, Pine Valley.”
  7. Departure: “Pine Valley traffic, Cessna 1234X, departing runway 27, departing the pattern to the north, climbing to 3,500, Pine Valley.”
Say the airport name first and last. Use runway numbers, never "active runway." · StudentPilot.com

Pine Valley and N1234X are made-up examples. If you are still nervous about the microphone, start with your first radio call and the phonetic alphabet.

Crosswinds push the whole pattern around. Crab on downwind to stay a constant distance from the runway, and expect a stronger or weaker ground speed on base. Our crosswind landings guide covers the final approach.

Gear for flying the pattern

A handheld backup radio keeps you talking if the panel radio quits, a kneeboard holds your airport notes and radio card, and the Chart Supplement and FAR/AIM are where the pattern altitude, right-traffic runways and rules live.

What you'll need

Practical gear for pattern work and non-towered airports.

Icom IC-A25C-S Sport Handheld Radio
Icom IC-A25C-S Sport Handheld Radio
Flight Outfitters iDeck Dual Device Kneeboard
Flight Outfitters iDeck Dual Device Kneeboard
FAA Chart Supplement SE
FAA Chart Supplement SE

Choosing a backup radio? See our handheld aviation radio guide.

Frequently asked questions

What are the legs of a traffic pattern?

The traffic pattern has departure (with the upwind leg as its extension), crosswind, downwind, base and final approach. Departure and upwind run along the extended centerline after takeoff, crosswind is at right angles off the departure end, downwind runs parallel to the runway opposite the landing direction, base is at right angles off the approach end, and final is lined up with the runway.

What is the standard traffic pattern altitude?

AIM 4-3-3 recommends 1,000 feet AGL for propeller-driven airplanes and at least 1,500 feet AGL for large and turbine-powered airplanes, unless the Chart Supplement publishes a different pattern altitude for that airport. Add the field elevation to get the MSL altitude you will see on your altimeter.

Are traffic pattern turns always to the left?

Left turns are standard. Under 14 CFR 91.126(b), at a non-towered airport in Class G airspace, powered fixed-wing aircraft approaching to land must turn left unless light signals or visual markings call for right turns. Right traffic is charted as RP followed by the runway numbers, and at a towered airport you follow the tower’s instructions.

How do you enter the traffic pattern at a non-towered airport?

Determine the runway in use from the CTAF, wind indicator and other traffic, get to pattern altitude well clear of the pattern, then join the downwind leg at a 45 degree angle abeam the midpoint of the runway. AC 90-66C also describes a midfield crossing entry, which should not be used when the pattern is congested.

When should you turn crosswind after takeoff?

Continue straight ahead until beyond the departure end of the runway, and begin the crosswind turn within 300 feet of pattern altitude. To leave the pattern, continue straight out or make a 45 degree turn in the direction of the pattern after reaching pattern altitude.

What radio calls should you make in the pattern?

AIM 4-1-9 recommends self-announcing on the CTAF about 10 miles out, entering downwind, on base, on final and when clear of the runway, plus before taxi and before taking the runway on departure. Say the airport name at the beginning and end of each call and use the runway number.

Back to the Airport Operations guide