StudentPilot.com is a PilotMall.com publicationShop pilot supplies ›

Holding Pattern Entry: Direct, Teardrop, Parallel (Diagrams)

A holding pattern entry is the FAA-recommended way to turn into a hold when you first reach the holding fix: direct, teardrop or parallel. Which one you use depends on your heading as you arrive, measured against a line drawn through the fix 70 degrees from the holding course: the parallel sector covers 110 degrees, the teardrop sector 70 degrees and the direct sector the remaining 180 degrees. A standard hold uses right turns and 1 minute inbound legs at or below 14,000 feet MSL.

This guide follows AIM paragraph 5-3-8, Holding (Change 3, effective July 9, 2026) and the FAA Instrument Procedures Handbook (FAA-H-8083-16B). It is part of our instrument rating guide.

Parts of a holding pattern

Standard right-turn holding pattern with holding fix, inbound leg, fix end turn, outbound leg, abeam position, outbound end turn, holding side and nonholding side labeled Holding fix Inbound leg (toward the fix) Outbound leg Fix end Outbound end Abeam the fix: start outbound timing Holding side Nonholding side Standard pattern: right turns. Nonstandard: left turns, holding side on the other side.
A standard (right-turn) holding pattern, no wind. Diagram by StudentPilot.com based on AIM 5-3-8 terminology.
  • Holding fix: the NAVAID, intersection, DME fix or waypoint you hold at.
  • Inbound leg: the leg flown toward the fix on the holding course. Its length is what you time.
  • Fix end and outbound end: the two 180 degree turns.
  • Outbound leg: flown away from the fix, parallel to the inbound course, on the holding side.
  • Holding side and nonholding side: the pattern sits on the holding side of the inbound course.

Standard vs nonstandard holds

AIM 5-3-8 defines a standard pattern as right turns and a nonstandard pattern as left turns. ATC tells you the direction of turns only if left turns are required, if you ask, or if the controller thinks it is necessary. If you hear nothing about turns, hold with right turns. Entries to a nonstandard hold use the same logic, mirrored: they are oriented to the 70 degree line on the holding side.

The three holding pattern entries

Holding entry sectors for a standard hold: parallel sector of 110 degrees, teardrop sector of 70 degrees and direct sector of 180 degrees, divided by the inbound course and a line through the fix 70 degrees from the holding course (a) Parallel 110 degrees (b) Teardrop 70 degrees (c) Direct 180 degrees 70 degree line Inbound course Hold (right turns) Sector = where you come from as you reach the fix Fix at center. Holding side above the inbound course.
Entry sectors for a standard hold, no wind. The inbound course runs right to left into the fix; the 70 degree line passes through the fix at 70 degrees from the holding course. Diagram by StudentPilot.com based on AIM FIG 5-3-4 (Holding Pattern Entry Procedures).

The AIM describes three recommended entries. The protected airspace around a hold was designed assuming you fly one of them, at or below the maximum holding speed.

  • Direct (sector c): fly to the fix and turn to follow the holding pattern. This covers the 180 degrees roughly aligned with the inbound course and the holding side.
  • Teardrop (sector b): fly to the fix, turn outbound to a heading 30 degrees from the outbound course into the holding side for 1 minute, then turn in the direction of the hold to intercept the inbound course.
  • Parallel (sector a): at the fix, turn to a heading parallel to the outbound course on the nonholding side for 1 minute, then turn toward the holding side (a left turn in a standard hold, as AIM FIG 5-3-4 shows) through more than 180 degrees and return to the fix or intercept the inbound course.

Any of the three gets you in safely if flown properly; AIM 5-3-8 notes other techniques may work, but these three are the FAA’s recommended entries and the basis for the holding airspace design.

How to determine your holding entry

AIM 5-3-8 says to choose the entry from your heading as you arrive at the fix, and a heading within plus or minus 5 degrees of a sector boundary is acceptable either way. A simple arithmetic method that matches the AIM figure:

  1. Work out the outbound course (the inbound course plus or minus 180).
  2. Subtract the outbound course from your heading to the fix, giving a number between -180 and +180.
  3. For a standard (right) hold: 0 to +110 is a parallel entry, 0 to -70 is a teardrop, anything else is direct.
  4. For a nonstandard (left) hold, flip the signs: 0 to -110 is parallel, 0 to +70 is teardrop, anything else is direct.

Example: “Hold north of the VOR on the 360 radial,” right turns. The inbound course is 180, so the outbound course is 360. Arriving on a heading of 090: 90 minus 360 is +90, a parallel entry. Arriving on 330: -30, a teardrop. Arriving on 200: -160, a direct entry. Many pilots instead picture the hold on the heading indicator; use whichever method you can do quickly and correctly under workload, and confirm it with your instructor.

Figure out the entry as soon as you receive the clearance, not at the fix. Write the hold on your kneeboard: fix, inbound course, turn direction, leg length, entry and EFC time. Then slow down before you get there.

Holding timing, speeds and turns

The inbound leg is timed, not the outbound leg. Per AIM 5-3-8:

  • Inbound leg time: 1 minute at or below 14,000 feet MSL; 1 1/2 minutes above 14,000 feet MSL.
  • First outbound leg: fly 1 minute (or 1 1/2 above 14,000), then adjust later outbound legs to make the inbound leg the right length.
  • Start outbound timing over or abeam the fix, whichever occurs later. If you cannot tell when you are abeam, start when the turn to outbound is complete.
  • DME or GPS holds use distances instead of time; the clearance or chart gives the outbound leg length.
  • Turns: 3 degrees per second, 30 degrees of bank, or 25 degrees with a flight director, whichever needs the least bank.
Altitude (MSL) Maximum holding airspeed
MHA to 6,000 ft 200 KIAS
6,001 to 14,000 ft 230 KIAS
14,001 ft and above 265 KIAS

Exceptions apply: some holds are charted with a lower limit (for example 210 KIAS between 6,001 and 14,000 feet, or a speed shown in parentheses inside the pattern), USAF fields use 310 KIAS and Navy fields 230 KIAS unless charted otherwise. When you are 3 minutes or less from a clearance limit without a further clearance, start slowing so you cross the fix at or below the maximum holding speed. The AIM also recommends fixed-wing aircraft hold at 90 KIAS or faster to limit wind drift. Most trainers hold well below these limits; use the speed in your POH or your instructor’s profile.

Wind correction in the hold

Correct for wind mainly with drift correction on both straight legs. AIM 5-3-8 says to triple the inbound drift correction on the outbound leg, in the opposite direction: if you hold 8 degrees left inbound, hold 24 degrees right outbound. For headwind and tailwind, adjust the outbound time so the inbound leg comes out to 1 minute. Our wind correction angle guide covers the basics.

Holding clearances: published and unpublished holds

When ATC clears you to a fix other than your destination and expects a delay, AIM 5-3-8 says the controller issues complete holding instructions (unless the hold is charted), an expect further clearance (EFC) time, and a best estimate of any additional delay. If the hold is published on your chart, the controller may simply say the direction and “as published,” for example “hold east of MIKEY as published, expect further clearance at 1521.” You can always ask for complete instructions.

For an unpublished hold, the clearance includes:

  1. Direction of holding from the fix, using the eight cardinal points (N, NE, E, and so on)
  2. The holding fix (may be omitted if it was the clearance limit)
  3. The radial, course, bearing, airway or route to hold on
  4. Leg length in miles if DME or RNAV is used
  5. Direction of turns, if left turns are required
  6. The EFC time and any additional delay information

If you reach a clearance limit without holding instructions, the AIM says to ask before reaching the fix. If you still cannot get them, hold in a standard pattern on the course on which you approached the fix and request further clearance as soon as possible.

Reporting in the hold

AIM 5-3-8 asks you to report to ATC the time and altitude at which you reach the clearance limit, and to report leaving it. AIM 5-3-3 lists both among the reports to make at all times, radar or not, without a specific ATC request. If you lose two-way radio communication, 14 CFR 91.185 governs when you leave the hold, using your EFC time. Our lost communications guide explains it step by step.

Holding pattern summary
AIM 5-3-8, standard pattern unless told otherwise
  • Turns: standard = right; nonstandard = left (ATC states left turns).
  • Entry (right hold): heading minus outbound course: 0 to +110 parallel, 0 to -70 teardrop, else direct. Plus or minus 5 degrees is fine.
  • Teardrop: 30 degrees into holding side, 1 min, turn to intercept inbound.
  • Parallel: outbound on nonholding side, 1 min, turn back toward the holding side (left, in a standard hold) through more than 180.
  • Timing: inbound 1 min at or below 14,000 MSL; 1 1/2 above. Outbound timing starts over or abeam the fix.
  • Max speed: 200 KIAS to 6,000; 230 to 14,000; 265 above.
  • Wind: triple the inbound drift correction outbound.
  • Clearance: direction, fix, radial/course, leg length, turns, EFC.
  • Report: time and altitude reaching the fix; report leaving.
Verify any charted speed limit or leg length on the procedure you are flying. · StudentPilot.com

Practicing holds

Holding is Task IR.III.B, Holding Procedures, in the Instrument Rating Airplane ACS (FAA-S-ACS-8C), and examiners love to ask about entries and timing in the oral. Practice entries on paper until they are automatic, then fly them with a view-limiting device. A holding visualizer lets you rotate a hold to any heading and see the entry instantly.

What you'll need

Study and training tools for holding patterns.

ASA IFR Holding Pattern Visualizer
ASA IFR Holding Pattern Visualizer
ASA Instrument Flying Handbook (FAA-H-8083-15B)
ASA Instrument Flying Handbook (FAA-H-8083-15B)
Gleim Instrument Pilot Oral Exam Guide
Gleim Instrument Pilot Oral Exam Guide
Foggles IFR Training Glasses
Foggles IFR Training Glasses

Keep going: file the flight with our IFR flight plan guide, see where holding falls in the Instrument Rating ACS, drill the instrument oral exam, and read about view-limiting devices and staying sharp with instrument currency, which requires logged holding procedures and tasks within the preceding 6 calendar months (14 CFR 61.57(c)).

Frequently asked questions

What are the three holding pattern entries?

The FAA recommends three entries: direct, teardrop and parallel. Direct means flying to the fix and turning into the pattern. Teardrop means turning 30 degrees into the holding side for 1 minute, then turning to intercept the inbound course. Parallel means flying parallel to the outbound course on the nonholding side for 1 minute, then turning back through more than 180 degrees.

How do you determine a holding pattern entry?

Use your heading as you reach the fix. A line through the fix at 70 degrees to the holding course divides the area into a 110 degree parallel sector, a 70 degree teardrop sector and a 180 degree direct sector. For a right-turn hold, subtract the outbound course from your heading: 0 to +110 is parallel, 0 to -70 is teardrop, and everything else is direct.

What is a standard holding pattern?

A standard holding pattern uses right turns, with a 1 minute inbound leg at or below 14,000 feet MSL and 1 1/2 minutes above 14,000 feet MSL. A nonstandard pattern uses left turns, and ATC will tell you when left turns are required.

What are the maximum holding airspeeds?

AIM 5-3-8 lists 200 KIAS from the minimum holding altitude through 6,000 feet MSL, 230 KIAS from 6,001 through 14,000 feet, and 265 KIAS at 14,001 feet and above, unless a lower speed is charted for that hold.

How do you correct for wind in a holding pattern?

Use drift correction on both legs and triple the inbound wind correction angle on the outbound leg, in the opposite direction. Adjust the outbound leg time so that the inbound leg takes the required 1 minute or 1 1/2 minutes.

What does ATC include in a holding clearance?

For a hold that is not charted, ATC gives the direction of holding from the fix, the fix, the radial or course to hold on, leg length if DME or RNAV is used, direction of turns if left turns are required, and an expect further clearance time.

Back to the Instrument Rating guide