The instrument oral exam is the ground portion of your instrument checkride: a scenario-based discussion with the examiner, built on the FAA’s Instrument Rating Airplane ACS (FAA-S-ACS-8C), that you must pass before the flight begins. Below are 72 instrument oral exam questions with short answers checked against the current eCFR, AIM, and FAA handbooks, grouped by ACS Area and Task.
This page is part of our Instrument Rating guide. Every question below maps to a Task in the Instrument ACS, and the oral leads straight into the flight; see the full instrument checkride walkthrough.
How the instrument oral exam works
The practical test has a ground portion and a flight portion. The ACS requires you to pass the ground portion before the flight begins, and questioning continues throughout the flight. Failing any Task fails the test.
What the examiner is really assessing
For each applicable Task, the examiner must test at least one knowledge element and one risk management element, plus any element you missed on the knowledge test. Expect a scenario built around an IFR cross-country the examiner assigns, with weather, equipment failures, and clearance changes woven in. The ACS favors applying knowledge to a situation over reciting rules.
The mock oral tool below picks a random question from this bank so you can answer out loud before checking the answer.
Answers assume a typical single-engine piston trainer flown under Part 91; your POH or AFM and avionics supplements govern where they differ.
Area I: Preflight Preparation
Task A. Pilot Qualifications (IR.I.A)
What do you need to act as pilot in command under IFR?
An instrument rating on your pilot certificate for the category and class of aircraft (or an ATP certificate), instrument currency under 61.57(c), and the usual PIC requirements such as a current flight review and a medical certificate or BasicMed.
Reference: 14 CFR 61.3(e), 61.57(c), 61.56
What are the instrument currency requirements?
Within the 6 calendar months preceding the month of the flight, you must have performed and logged six instrument approaches, holding procedures and tasks, and intercepting and tracking courses through navigational electronic systems. They can be flown in actual or simulated conditions, or in a full flight simulator, flight training device, or aviation training device representing the aircraft category.
Reference: 14 CFR 61.57(c)(1), (c)(2)
Your instrument currency lapsed four months ago. Do you need an IPC?
No. Until you have been out of currency for more than six calendar months, you can regain it by flying the required approaches, holding, and tracking with a safety pilot or in an approved device. After that, only an instrument proficiency check restores it. See our currency and IPC guide.
Reference: 14 CFR 61.57(c), (d)
Who can give an IPC, and what does it cover?
An examiner, an authorized instructor (CFII), or another person listed in 61.57(d)(3). It follows the Instrument ACS IPC table: holding, unusual attitudes, intercepting and tracking, all approach Tasks, the partial panel approach, postflight, and the engine-out Tasks in a multiengine airplane.
Reference: 14 CFR 61.57(d); FAA-S-ACS-8C, Appendix 1
What must you log to show instrument currency?
The location and type of each instrument approach, and the name of the safety pilot if one was required.
Reference: 14 CFR 61.51(g)(3)
What are the requirements for a safety pilot?
For simulated instrument flight, the other control seat must be occupied by a safety pilot with at least a private pilot certificate with category and class ratings appropriate to the aircraft, with adequate vision forward and to each side (or a competent observer supplementing it). The aircraft needs fully functioning dual controls, with a narrow throwover-wheel exception.
Reference: 14 CFR 91.109(c); see our view-limiting devices guide
Task B. Weather Information (IR.I.B)
Which weather products do you check before an IFR flight?
The ACS lists METARs, SPECIs, and PIREPs; the surface analysis and ceiling and visibility charts; TAFs; the Graphical Forecasts for Aviation; winds and temperatures aloft; the convective outlook; and AIRMETs, SIGMETs, and convective SIGMETs. See our METAR and TAF guide.
Reference: FAA-S-ACS-8C, IR.I.B.K2; AIM 7-1-4, 7-1-6
What hazards do AIRMETs cover?
IFR conditions (ceiling below 1,000 feet and/or visibility below 3 miles), widespread mountain obscuration, moderate icing and freezing levels, moderate turbulence, non-convective low-level wind shear below 2,000 feet AGL, and sustained surface winds greater than 30 knots.
Reference: AIM 7-1-6
When is a convective SIGMET issued?
For severe thunderstorms with surface winds of 50 knots or more, surface hail of 3/4 inch or more, or tornadoes; embedded thunderstorms; a line of thunderstorms; or heavy-precipitation thunderstorms covering at least 40 percent of an area of 3,000 square miles or more. Any convective SIGMET implies severe or greater turbulence, severe icing, and low-level wind shear.
Reference: AIM 7-1-6
What conditions are needed for structural icing, and which type is most dangerous?
Visible moisture and a temperature at or below 0 °C, though aerodynamic cooling can cause icing slightly above freezing. Clear ice, formed from large droplets or freezing rain, is the most dangerous because it is hard to see and changes the shape of the airfoil.
Reference: FAA-H-8083-15B, Chapter 10
You start picking up ice in the clouds. What do you do?
Get out of the visible moisture: descend below the bases, climb above the tops, or turn, and if that is not possible move to an altitude where the temperature is above freezing. Report the icing to ATC and request a new routing or altitude.
Reference: FAA-H-8083-15B, Chapter 10; AIM 7-1-19
How far should you stay from a severe thunderstorm?
At least 20 miles from any thunderstorm identified as severe or giving an intense radar echo, especially under the anvil. Severe turbulence can extend up to 20 miles from severe storms. See our weather hazards guide.
Reference: AIM 7-1-26, 7-1-27
Can you use datalink radar on your tablet to pick a path between storm cells?
No. Flight Information Services weather such as ground-based radar imagery is for strategic decisions (about 20 minutes or more ahead) like avoiding a whole area, not tactical navigation through a hazard. It also does not replace a preflight briefing.
Reference: AIM 7-1-9
Task C. Cross-Country Flight Planning (IR.I.C)
When do you need to file an alternate?
Always, unless the destination has a standard instrument approach and the forecast for 1 hour before to 1 hour after your ETA shows a ceiling of at least 2,000 feet above airport elevation and visibility of at least 3 statute miles. This is the “1-2-3 rule.”
Reference: 14 CFR 91.169(a)(2), (b)
What weather must the alternate have to be listed?
At your ETA there, the alternate minimums published for its approach, or if none are published, a ceiling of 600 feet and 2 statute miles for a precision approach or 800 feet and 2 statute miles for a non-precision approach. With no instrument approach at all, the weather must allow descent from the MEA, approach, and landing under basic VFR.
Reference: 14 CFR 91.169(c)
What do the “A” symbol and “A NA” mean on an approach chart?
A triangle with an “A” means the airport has nonstandard alternate minimums, listed in the Alternate Minimums section of the Terminal Procedures Publication. “A NA” means alternate minimums are not authorized, for example because of an unmonitored facility or no weather reporting.
Reference: FAA-H-8083-15B, Chapter 1
How much fuel do you need for an IFR flight?
Enough to fly to the first airport of intended landing, then to the alternate if one is required, and then for 45 minutes at normal cruising speed, considering weather reports and forecasts. Our IFR flight plan guide shows where the alternate and fuel go on the form.
Reference: 14 CFR 91.167(a)
With a non-WAAS GPS, can you plan a GPS approach at both the destination and the alternate?
No. With FDE capability and a preflight RAIM prediction you may base the plan on a GPS approach at the destination or the alternate, but not both. Otherwise the required alternate must have a non-GPS approach you can fly.
Reference: AIM 1-1-17
With a WAAS GPS, which minimums do you use when planning an alternate?
Plan on the LNAV or circling line (or an “or GPS” conventional procedure) using non-precision weather requirements. On arrival, if the receiver shows LPV or LNAV/VNAV available, you may use that vertical guidance.
Reference: AIM 1-1-18
What is the minimum IFR altitude where none is published?
2,000 feet above the highest obstacle within 4 nautical miles of course in a designated mountainous area, or 1,000 feet above the highest obstacle within 4 nautical miles elsewhere.
Reference: 14 CFR 91.177(a)(2)
What altitude do you fly IFR in uncontrolled airspace below 18,000 feet?
On a magnetic course of 0 to 179 degrees, odd thousands (3,000, 5,000); on 180 to 359 degrees, even thousands (4,000, 6,000). In controlled airspace you fly the altitude ATC assigns.
Reference: 14 CFR 91.179
Area II: Preflight Procedures
Task B. Aircraft Flight Instruments and Navigation Equipment (IR.II.B)
What two gyroscopic principles do the flight instruments use?
Rigidity in space and precession. The attitude and heading indicators rely on rigidity; the turn coordinator and turn indicator rely on precession.
Reference: FAA-H-8083-15B, Chapter 5
What does the turn coordinator show?
First the rate of roll, then once the bank is stabilized the rate of turn; a standard rate turn is 3 degrees per second. The inclinometer ball shows whether the turn is coordinated.
Reference: FAA-H-8083-15B, Chapter 5
Why do you reset the heading indicator in flight?
Precession causes it to drift, so standard practice is to compare it with the magnetic compass at least every 15 minutes and reset it as necessary.
Reference: FAA-H-8083-15B, Chapter 5
Your static port ices over and you select alternate static. What changes?
In most unpressurized airplanes the cabin pressure is slightly lower, so the altimeter reads slightly high, the airspeed indicator reads high, and the VSI shows a momentary climb. See our pitot-static system guide.
Reference: FAA-H-8083-15B, Chapter 5
What is RAIM, and how many satellites does it need?
Receiver autonomous integrity monitoring lets the GPS receiver check the integrity of its own position. It needs 5 satellites, or 4 plus baro-aiding; fault detection and exclusion needs 6, or 5 plus baro-aiding.
Reference: AIM 1-1-17
If your IFR GPS is not WAAS, what else must you carry?
An alternate approved and operational means of navigation suitable for the route, such as VOR. You must actively monitor it whenever RAIM is lost.
Reference: AIM 1-1-17
Can you fly a GPS approach with an expired database?
Plan on a current database. The AIM says approaches must be retrievable by name from the current airborne navigation database, and manually entered waypoints are not permitted for approaches. Its GPS approval table allows an approach with an expired database only if you verify the procedure has not been amended since the database expired, and your AFM supplement may be stricter. See our GPS and EFB guide.
Reference: AIM 1-1-17
What is the difference between LPV, LNAV/VNAV, LP, and LNAV minimums?
LPV and LNAV/VNAV have vertical guidance and are flown to a decision altitude. LP and LNAV are lateral only and are flown to an MDA; LP uses WAAS for tighter lateral guidance and is published only where vertical guidance cannot be.
Reference: AIM 5-4-5, 1-1-18
Task C. Instrument Flight Deck Check (IR.II.C)
What equipment does 91.205 require for IFR beyond VFR equipment?
Two-way radio and navigation equipment suitable for the route, a gyroscopic rate-of-turn indicator (with a narrow exception), a slip-skid indicator, a sensitive altimeter adjustable for barometric pressure, a clock with hours, minutes, and seconds, an adequate generator or alternator, an attitude indicator, and a heading indicator.
Reference: 14 CFR 91.205(d)
Which inspections must be current for IFR?
Beyond the VFR inspections, the altimeter, static system, and altitude reporting checks within 24 calendar months for IFR in controlled airspace, the transponder check within 24 calendar months, and a VOR check within 30 days if you will use VOR. Our AV1ATES memory aid covers the full list.
Reference: 14 CFR 91.411, 91.413, 91.171
What are the VOR check tolerances?
Plus or minus 4 degrees with a VOT or a designated ground checkpoint, plus or minus 6 degrees with an airborne checkpoint or a prominent point along an airway centerline, and 4 degrees between two independent receivers. Log the date, place, bearing error, and your signature.
Reference: 14 CFR 91.171(b), (c), (d)
The heading indicator is inoperative and there is no MEL. Can you go IFR?
No. Inoperative equipment can be deferred under 91.213(d) only if it is not required by 91.205 for the kind of operation, and 91.205(d) requires a heading indicator for IFR.
Reference: 14 CFR 91.213(d), 91.205(d)
Area III: Air Traffic Control Clearances and Procedures
Task A. Compliance with ATC Clearances (IR.III.A)
What does an IFR clearance contain?
The clearance limit, departure procedure, route, altitude, and holding instructions when needed, plus items such as a departure control frequency and transponder code. Many pilots copy it in the order C-R-A-F-T: clearance limit, route, altitude, frequency, transponder.
Reference: AIM 4-4-3, 5-2-6
What is a clearance void time, and what if you miss it?
At an airport without an operating tower, the clearance is void if you are not airborne by that time. If you do not depart, tell ATC as soon as possible and no later than 30 minutes after the void time, or search and rescue may begin.
Reference: AIM 5-2-7
When may you deviate from an ATC clearance?
When you get an amended clearance, in an emergency, or in response to a TCAS resolution advisory, and you must notify ATC of the deviation as soon as possible. If you are unsure of a clearance, ask for clarification immediately.
Reference: 14 CFR 91.123(a), (c); 91.3(b)
What must you report to ATC without being asked?
Among others: vacating an assigned altitude, being unable to climb or descend at least 500 feet per minute, a missed approach, a TAS change of 5 percent or 10 knots (whichever is greater) from the flight plan, reaching and leaving a holding fix, and any loss of navigation or communication capability, including the equipment affected and the help you need. Report unforecast weather and anything affecting safety of flight.
Reference: AIM 5-3-3; 14 CFR 91.183, 91.187
Task B. Holding Procedures (IR.III.B)
What does a clearance to hold at an uncharted fix include?
The direction of holding from the fix, the holding fix, the radial or course to hold on, leg length if DME or RNAV is used, the direction of turns if left turns are required, and an expect further clearance time.
Reference: AIM 5-3-8
What are the three recommended holding entries?
Direct, teardrop, and parallel, chosen by which sector you approach the fix from, using the 70-degree line on the holding side. Our holding patterns guide diagrams each one.
Reference: AIM 5-3-8
What are the maximum holding airspeeds?
200 KIAS from the minimum holding altitude through 6,000 feet MSL, 230 KIAS from 6,001 through 14,000 feet, and 265 KIAS above 14,000 feet, unless a different maximum is published.
Reference: AIM 5-3-8
How long are the legs in a holding pattern?
The inbound leg is 1 minute at or below 14,000 feet MSL and 1 1/2 minutes above. Adjust outbound timing, which starts over or abeam the fix (whichever is later), to get the right inbound time.
Reference: AIM 5-3-8
When should you slow to holding speed?
Start the speed reduction so you cross the fix at or below maximum holding speed, beginning when 3 minutes or less from the fix. The ACS skill standard says the same.
Reference: AIM 5-3-8; FAA-S-ACS-8C, IR.III.B.S2
You get an unexpected EFC 40 minutes away. What do you think about?
Recalculate fuel against the 45-minute reserve and your alternate, and decide whether to divert. If fuel leaves no room for undue delay, advise ATC “minimum fuel”; if you need priority to land safely, declare an emergency and report fuel remaining in minutes.
Reference: FAA-S-ACS-8C, IR.III.B.R1, R2; AIM 5-5-15; 14 CFR 91.167
Area IV: Flight by Reference to Instruments
Task A. Instrument Flight (IR.IV.A)
What are the common instrument scan errors?
Fixation (staring at one instrument), omission (leaving an instrument out of the cross-check), and emphasis (relying on one instrument instead of the combination).
Reference: FAA-H-8083-15B, Chapter 6
About what bank angle gives a standard rate turn?
A rule of thumb is airspeed divided by 10, plus 7. At 90 knots that is about 16 degrees.
Reference: FAA-H-8083-15B, Chapter 4
Describe the leans and the graveyard spiral.
The leans: after a slow, unnoticed bank, an abrupt correction makes you feel banked the other way. The graveyard spiral: in a prolonged turn you feel level, notice altitude loss, and pull back, which tightens the descending spiral.
Reference: FAA-H-8083-15B, Chapter 3; AIM 8-1-5
What are the Coriolis and somatogravic illusions?
Coriolis: moving your head during a prolonged turn creates the sensation of rotating on another axis. Somatogravic: rapid acceleration, as on takeoff, feels like a nose-up attitude and can lead you to push the nose down.
Reference: FAA-H-8083-15B, Chapter 3
Task B. Recovery from Unusual Flight Attitudes (IR.IV.B)
How do you recover from a nose-high unusual attitude?
Follow the POH if it has a procedure. Otherwise, with airspeed decreasing: add power, lower the nose with forward pressure to prevent a stall, then level the wings with coordinated aileron and rudder, nearly simultaneously but in that order.
Reference: FAA-H-8083-15B, Chapter 7
How do you recover from a nose-low unusual attitude?
With airspeed increasing: reduce power, level the wings with coordinated aileron and rudder using the turn coordinator, then raise the nose smoothly to level flight. The instinctive reaction to pull back first is the error to avoid.
Reference: FAA-H-8083-15B, Chapter 7
Area V: Navigation Systems
Task A. Intercepting and Tracking Navigational Systems and DME Arcs (IR.V.A)
What tracking standard does the ACS hold you to?
No more than 3/4-scale CDI deflection, airspeed plus or minus 10 knots, altitude plus or minus 100 feet, and headings plus or minus 5 degrees. A DME arc must be held within 1 nautical mile.
Reference: FAA-S-ACS-8C, IR.V.A.S5, S6
How does GPS CDI sensitivity change during an approach?
It is plus or minus 5 NM en route, changes to plus or minus 1 NM terminal sensitivity within 30 NM of the airport when the approach is armed, and ramps to plus or minus 0.3 NM over the 2 NM before the final approach waypoint.
Reference: AIM 1-1-17
Task B. Departure, En Route, and Arrival Operations (IR.V.B)
What is the difference between an ODP and a SID?
An obstacle departure procedure provides obstacle clearance and may be flown without ATC clearance unless ATC assigns something else. A standard instrument departure is an ATC procedure that also reduces workload, and you must be cleared for it.
Reference: AIM 5-2-9
What climb performance do departure procedures assume?
Crossing the departure end of the runway at least 35 feet above it, climbing to 400 feet above it before turning, and at least 200 feet per nautical mile to the minimum IFR altitude unless a higher gradient is published.
Reference: AIM 5-2-9
Are Part 91 pilots bound by IFR takeoff minimums?
Not by regulation: the takeoff minimums in 91.175(f) apply to Parts 121, 125, 129, and 135. The AIM still tells every IFR pilot to check the takeoff obstacle notes, decide whether obstacles can be avoided visually or the ODP should be flown, and strongly encourages Part 91 pilots to file and fly a departure procedure at night, in marginal VMC, and in IMC.
Reference: 14 CFR 91.175(f); AIM 5-2-9
Area VI: Instrument Approach Procedures
Tasks A and B. Non-precision and Precision Approaches (IR.VI.A, IR.VI.B)
What determines your authorized DA or MDA?
The highest of the DA or MDA on the procedure, any prescribed for the pilot in command, and the one appropriate to the equipment available and used on the approach.
Reference: 14 CFR 91.175(b)
When can you descend below DA or MDA?
Only when you are continuously in position to land on the intended runway at a normal rate of descent using normal maneuvers, the flight visibility is at least the approach minimum, and at least one required visual reference for the runway is distinctly visible and identifiable.
Reference: 14 CFR 91.175(c)
You see only the approach lights at DA. How low can you go?
You may continue, but not below 100 feet above touchdown zone elevation on the approach lights alone unless the red terminating bars or red side row bars are also distinctly visible. See our airport lighting guide.
Reference: 14 CFR 91.175(c)(3)(i)
What is a visual descent point?
A point on a straight-in non-precision final, marked with a “V,” from which a normal descent from the MDA to the touchdown point can begin. Do not descend below the MDA before reaching it.
Reference: AIM 5-4-5
When is a procedure turn not allowed?
When the segment is marked “NoPT,” when you are radar vectored to the final approach course or fix, or on a timed approach from a holding fix, unless ATC clears you for it.
Reference: 14 CFR 91.175(j); AIM 5-4-9
You are cleared for the approach while being vectored. What altitude do you fly?
Maintain the last assigned altitude until established on a segment of a published route or the approach, then descend to the published altitudes for each segment.
Reference: 14 CFR 91.175(i)
Task C. Missed Approach (IR.VI.C)
When must you execute a missed approach?
Immediately, if the 91.175(c) conditions are not met while below MDA or at the missed approach point or DA and any time after until touchdown, or if an identifiable part of the airport is not distinctly visible while circling at or above MDA.
Reference: 14 CFR 91.175(e)
You decide to go missed before reaching the missed approach point. Can you turn right away?
No, unless ATC clears otherwise. Fly the approach to the missed approach point at or above the MDA or DH before turning, because obstacle protection assumes the missed approach starts there.
Reference: AIM 5-4-21
Task D. Circling Approach (IR.VI.D)
How is your aircraft approach category determined?
By VREF, or 1.3 VSO at maximum certificated landing weight if VREF is not specified: Category A is under 91 knots and B is 91 to under 121 knots. If you circle faster than your category’s range, use the higher category’s minimums.
Reference: 14 CFR 97.3; AIM 5-4-7
You lose sight of the airport while circling. What do you do?
Go missed: make an initial climbing turn toward the landing runway and continue the turn until established on the published missed approach course.
Reference: AIM 5-4-21; 14 CFR 91.175(e)(2)
Task E. Landing from an Instrument Approach (IR.VI.E)
You see the runway at DA but flight visibility is below minimums. Can you land?
No. Under Part 91 you may not land when flight visibility is less than the visibility prescribed in the approach procedure being used.
Reference: 14 CFR 91.175(d)
Area VII: Emergency Operations
Task A. Loss of Communications (IR.VII.A)
You lose two-way radio in VFR conditions. What do you do?
Continue the flight under VFR and land as soon as practicable, which the AIM notes does not mean as soon as possible. Squawk 7600.
Reference: 14 CFR 91.185(b); AIM 6-4-1, 6-4-2
Lost comms in IMC: what route do you fly?
The route in the last clearance; if being vectored, direct to the fix, route, or airway in the vector clearance; otherwise the route ATC said to expect; otherwise the filed route (often remembered as AVEF).
Reference: 14 CFR 91.185(c)(1)
Lost comms in IMC: what altitude do you fly?
The highest of the last assigned altitude, the minimum IFR altitude for the segment being flown, or the altitude ATC said to expect, recalculated segment by segment (often remembered as MEA).
Reference: 14 CFR 91.185(c)(2); AIM 6-4-1
Lost comms: when do you leave the clearance limit and begin the approach?
If the limit is a fix where an approach begins, start descent and the approach as close as possible to the EFC time, or if none, your ETA from the filed or amended time en route. If the limit is not such a fix, leave it at the EFC (or on arrival if none) and proceed to an approach fix, beginning the approach as close as possible to your ETA.
Reference: 14 CFR 91.185(c)(3)
Task D. Approach with Loss of Primary Flight Instrument Indicators (IR.VII.D)
How would you recognize a vacuum pump failure?
The attitude and heading indicators slowly drift or tumble together while the turn coordinator (often electric), airspeed, altimeter, and VSI disagree with them, and the suction gauge reads low. Many small airplanes have no vacuum warning, so the gauge belongs in your scan.
Reference: FAA-H-8083-15B, Chapter 11
What do you do after an instrument failure in IMC?
Identify the failed instruments by comparison, fly with the remaining ones (covering the failed ones helps), try to restore the power source or backup, and advise ATC, declaring an emergency if needed. The ACS then expects a non-precision approach without the primary instruments.
Reference: FAA-H-8083-15B, Chapter 11; FAA-S-ACS-8C, IR.VII.D
Area VIII: Postflight Procedures
Task A. Checking Instruments and Equipment (IR.VIII.A)
An instrument acted up in flight. What do you do after landing?
Conduct the postflight inspection and document the discrepancy and any servicing needs so maintenance can address it before the next IFR flight. The ACS evaluates this as its own Task.
Reference: FAA-S-ACS-8C, IR.VIII.A
How to prepare for the instrument oral
- Read the ACS itself. The Instrument Rating Airplane ACS lists every element the examiner can test; our Instrument ACS guide explains the codes.
- Work your knowledge test report. The examiner must revisit the ACS codes you missed on the instrument written.
- Plan the assigned cross-country carefully. Expect to defend your route, altitudes, alternate, fuel, and go/no-go decision with real weather.
- Know your avionics. Be ready to explain your GPS, autopilot, and any EFB you plan to use, including their failure modes.
- Practice out loud. Do a mock oral with your instructor, then review the private pilot oral questions too, since airworthiness and human factors come up again.
If you are unsure, say so and show where you would find the answer in the FAR/AIM, the Chart Supplement, or the approach chart legend. Using resources is part of single-pilot resource management, which the ACS evaluates. A confident wrong answer is worse.
Instrument oral exam study guides
What you'll need
The guides and tools instrument students use to prepare for the oral, all from PilotMall.com.
Frequently asked questions
How long is the instrument oral exam?
The FAA does not set a length. The examiner must cover knowledge and risk management in every applicable ACS Task plus anything you missed on the written, so ask your examiner what to expect and plan for a long session.
What topics come up most on the instrument oral?
Expect currency and IPC rules, IFR equipment and inspections, alternate and fuel requirements, weather and icing, clearances, lost communications, holding, and approach minimums, usually tied to a cross-country scenario the examiner assigns.
Can you fail the instrument oral?
Yes. You must pass the ground portion before the flight, and failing any Task fails the test. You receive a Notice of Disapproval and keep credit for the Areas you passed if you complete the retest within 60 days and get any required additional training and endorsement.
Is the instrument oral based on the ACS?
Yes. FAA-S-ACS-8C defines the Tasks and elements the examiner tests, and the examiner must include any ACS codes listed on your knowledge test report.
What is the best way to study for the instrument oral?
Work through the ACS Task by Task, answer practice questions out loud, plan a real IFR cross-country with current weather, and do a mock oral with your instructor. An oral exam guide organized by ACS Task helps you find gaps.




